Showing posts with label Gambler. Show all posts
Showing posts with label Gambler. Show all posts

Tuesday, July 25, 2017

Gambler AG mods, beginners RC discus launched glider (DLG)

The Gambler AG is a great plane. Elsewhere on this blog is information about its construction. I've used the model a lot. On flat fields, its discus launch or off a bungee, but it's also fun to slope soar it. For towing, it needed a tow hook, so here's a picture of the one I made for it:

The tow hook is reinforced internally as shown here. Also, as I mentioned in previous posts, I got rid of the rudder pushrod. Here, through the foam guide, you can see the diamond hook of the new rudder control rod, where it attaches to the pull string of the return spring arrangement:

The elevator servo has stayed firmly placed over time, simply being glued down. I guess that loads on the rudder servo are greater, because in contrast, the rudder servo tended to move. I've also had to replace it twice. Fed up with trying to re-stick replacement rudder servos, I decided to make a mount for it, and this is what it looks like:

The servo screws are tightened using a cranked star screwdriver (which is a flash way of describing "one wot I bent!"). The rudder servo mount has been a major improvement. Apart from making it easier to replace servos, it has also improved rudder control finesse and centering. Will it stay put over the long term? Time will tell...

Monday, September 8, 2014

Pull Spring Servo linkage for DLG type glider rudder

My Gambler discus launched glider had a rattling rudder pushrod in the carbon boom. Also, it didn't move that smoothly. So, I decided to convert it to a pull-spring rudder. The first thing was to cut the old pushrod at the pod end, and tack some strong thread on it with CA glue. Pulling the pushrod out from the tail end allowed me to thread string through the boom with no fuss at all. I'm using BCY archery serving, which seems really strong, light and abrasion resistant. This is the thread emerging from the end and you can see where I tacked it to the old pushrod. 
The spring is simply really thin wire, sorry not sure the diameter, bent into a U shape with one leg off at an angle. (The torque is determined by the length of the spring and the thickness of the wire. I just guessed). So when you place the U on a table, one of the legs is flat to the table and the other one sticks up. I then carefully pushed each leg into the rudder near the horn and boom exit. Now, three things are important here. First, it's crucial to have the rudder horn on the other side of the plane from the throwing peg. That was already the case for me, so all good. Second, you need to think carefully about which orientation the spring goes, so that the servo and string are pulling in the right direction. Third, you should really have the bevelled edges of the rudder and fin exposed in order to push the spring legs in. However, the bevel side was on the other side, and I didn't want to remove the strong 3M Blenderm hinge tape. So, I went for it as it was. Here I've pushed one leg in, and am pushing the other in, feeding a drop of CA in as I push:
This is it pushed home. So to recap, one leg into the fin, the other into the rudder. 
Then tie off the string to the horn, a little drop of CA to secure the knot and I put a small piece of cloth tape over the spring - probably not really necessary:
Same thing at the other end. I kept a bit of wire leading to the servo, in order to have some adjustment for finding throw centre. 
It works really well. Much smoother and a tad daresay lighter than the pushrod arrangement. And happily, the rattle of the rods in the boom has gone! No issues (e.g. buzzing) due to the servo arm being under tension. That must mean I got the spring tension about right. So far, it's been very reliable. 

Monday, February 18, 2008

Chuck Glider discus launches Gambler AG

This is not a free flight glider. I've been dabbling with the "dark side" and my chosen weapon is the Gambler AG from Wright Brothers RC.

Why am I dabbling in the dark side (aka radio control)? Well, there is method in Chuck Glider's madness. The main reason for playing with RC is to learn about discus launching - what it feels like and how bad launches go!

The latest thing in free flight chuck gliders is the discus method of launching, also called tip launching. This is a field of aeromodelling where free flighters have learned from our radio control cousins (not the other way round, as is usually the case ;) ).

The Gambler is a fine model and I've thoroughly enjoyed flinging it about to play with low level thermals. Best flight so far is nearly 3 minutes
(in wintery conditions). I have not flown it in good thermic conditions yet and am looking forward to that!

The next stage would be to build a free flight DLG! So watch this space....
Google